Results 1 to 6 of 6

Thread: Mirror Imaging About The X-Axis With A Fanuc 18M Control...

  1. #1
    Join Date
    May 2009
    Location
    Queens, NY
    Posts
    9
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Mirror Imaging About The X-Axis With A Fanuc 18M Control...

    I am having a problem creating a mirror image of a simple program about the X-axis with a Fanuc 18M controller. It appears that I have to kill the main power and restart the machine before I can reset my work offset for the mirrored program. Am I doing this right,and if not can someone please explain the steps I must take when performing such a programing operation...

  2. #2
    Join Date
    May 2009
    Location
    Queens, NY
    Posts
    9
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Re: Mirror Imaging About The X-Axis With A Fanuc 18M Control...

    I am unable to read anyof the responses to my requestt for help. What is the problem?

  3. #3
    Join Date
    May 2009
    Location
    Queens, NY
    Posts
    9
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Re: Mirror Imaging About The X-Axis With A Fanuc 18M Control...

    Apparently, my post count has to be six posts or more to send my e-mail address, so I am assuming that our correspondence is never going to occur. Please excuse me for the inconvience for I am going to have to solve this issue elsewhere. Thank you for your responses, they are much appreciated regardless of the outcome...

  4. #4
    Join Date
    May 2009
    Location
    Queens, NY
    Posts
    9
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Re: Mirror Imaging About The X-Axis With A Fanuc 18M Control...

    Again, thank you for your input MumakilFluins, but I am still unable to read your responses. If you look at my user name, it will give you a clue as to how to contact me. In regards to my mirror imaging issue, I have yet to come across a solution to the problem...

  5. #5
    Join Date
    Oct 2008
    Posts
    664
    Thanks
    3
    Thanked 94 Times in 76 Posts

    Cool Re: Mirror Imaging About The X-Axis With A Fanuc 18M Control...

    Hello mwbishop71,

    I am not 100% sure but I think that what you see as an answer to your thread by that member named MumakilFluins is actually a fake reply from a fake user of this forum, I have seen it before somewhere else, and I can tell you that if it hasn't been erased yet is because our forum administrator hasn't seen it yet.

    Please be patient, today is Sunday and perhaps tomorrow you will get an answer (or several) to your thread.

    Best regards.

  6. #6
    Join Date
    Oct 2008
    Posts
    664
    Thanks
    3
    Thanked 94 Times in 76 Posts

    Default Re: Mirror Imaging About The X-Axis With A Fanuc 18M Control...

    Hello again,

    Now I am 100% sure that it is fake, at the bottom of "his" replies there is a link in red letters, I went there all armored with my best antivirus software just to make sure, well, it is a link to an adult-oriented site, please don't click on it.

    Once more, please be patient with your thread, you'll get an answer soon.
    Last edited by Sinumeriko; 08-02-09 at 10:12 PM.

Similar Threads

  1. axis lube: fanuc control
    By Guest in forum General CNC & Manufacturing Discussion
    Replies: 3
    Last Post: 10-19-10, 12:21 PM
  2. Disable C axis on 180i control
    By Gralyndr in forum Fanuc Controls
    Replies: 3
    Last Post: 09-04-10, 07:24 PM
  3. Replies: 1
    Last Post: 03-19-09, 02:40 PM
  4. A77 Synchronous Control Procedure - Y/V axis
    By AvicStuka in forum General CNC & Manufacturing Discussion
    Replies: 2
    Last Post: 02-07-09, 12:01 PM
  5. Z axis position is all screwed up. Fanuc 18M control. Supermax V56T
    By supermax73 in forum Machine Repair & Troubleshooting
    Replies: 2
    Last Post: 01-12-08, 09:01 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •