Results 1 to 6 of 6

Thread: Fanuc 6 system error 908

  1. #1
    hidivsultan Guest

    Default Fanuc 6 system error 908

    Hi

    I am receiving a system error 908 on our Fanuc 6. any suggestions?

    tnx

    Sean

  2. #2
    TNT Guest

    Default

    I dnt have the exact error msg in my reference, bt I can guess its for ROM trouble!!!! I got the Error 910 and a green light in the base PCB blinks!!! does that happen to you? I'm sure theres something wrong with the bubble memory, if you have?

  3. #3
    hidivsultan Guest

    Default

    I am not sure if it is the same but we called fanuc and they told us to throw it in the garbage! we did reset and delete parameters and still trying. We need the parameters now...Good luck!

  4. #4
    Join Date
    Mar 2006
    Location
    Singapore
    Posts
    13
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    Do you try to clear the system data / back up data. And use flash card to re-boot the system? What you need to do is to confirm wherther is Flash ROM / SRAM / your main CPU card have problem.... Good luck to you.

  5. #5
    Join Date
    Mar 2006
    Location
    Singapore
    Posts
    13
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default

    To enter the Boot screen :
    1. At power on time, press [ > ] and a soft key at its left.
    2. Place the cursor at SYSTEM DATA DELETE press [select] and [YES].
    3. After that, input the system data files from flash memory card to flash ROM. Place the cursor at SYSTEM DATA LOADING on the system monitor screen. [SELECT] > Place the cursor at the target files > [SELECT] > [YES].
    4. Place the cursor at [END] on the system monitor screen > [SELECT] > [YES].
    5. Your machine will auto start-up again. If the alarm comes again means the flash ROM can't boot-up. Ask FANUC agent to change for you.

    Any further question can email to me: Avic_stuka@hotmail.com

  6. #6
    EDM_Fixer Guest

    Default

    while machine is off .. pull the bubble mem. board ..there are some numbers on the piece of sheet metal (tells machine whats in it .. like how much mem) they are in 3 didget sets ,write um down.... ok put it back in ..turn on main power, now hold - & . while turning on machine. press 4 key, then press 2 key, now in the middle on the top of the mother board is the free bubble switch,, input the 3 didget deffective loop data,one set at a time,, done ? press start key, then reset , turn off power and reset free bubble switch ... try it ... hope it works ... have fun Jim

Similar Threads

  1. Problem with Fanuc 10T Check System Label Error
    By arincon in forum Machine Repair & Troubleshooting
    Replies: 0
    Last Post: 09-23-14, 03:55 PM
  2. 516 system error MAZAK QTN200IIM
    By Boris in forum Machine Repair & Troubleshooting
    Replies: 0
    Last Post: 07-25-13, 07:31 AM
  3. PMC System error
    By Azim in forum Machine Repair & Troubleshooting
    Replies: 5
    Last Post: 12-27-12, 05:32 AM
  4. 001 system error Milacron roboshot 55
    By alber in forum Machine Repair & Troubleshooting
    Replies: 0
    Last Post: 04-02-12, 12:02 PM
  5. Fanuc System Error
    By metalmelissa in forum Machine Repair & Troubleshooting
    Replies: 2
    Last Post: 08-06-09, 01:08 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •