Results 1 to 7 of 7

Thread: Need Help [Amada Fanuc AMADAN 04-PC] Error 220 & 221

  1. #1
    Join Date
    Oct 2012
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Need Help [Amada Fanuc AMADAN 04-PC] Error 220 & 221

    Hi all !!!
    I'm new here, and I'm not speaking english very well. Also, I need a help from an expert, I think.

    I have Amada punching machines: Pega 367 controler Fanuc Amadan 04PC

    Here's my problem

    1. When I turn on the machine at once I get an error 220 and 221
    2. Reset error and reference axes X, Y and Turret - all OK.
    3. Start the program - OK.
    4. First Strike - Machine stop and errors 220 221
    5. Em. stop
    6. Reset errors
    7. Reference axes
    8. Start the program
    9. first strike - Machine stop and errors 220 and 221

    This happens some times, but eventually the machine to operate normally until the end of work. The next day the same thing.

    I replaced the Y-axis servo but no change
    Perhaps the y-axis motor is broken? I have no idea
    Where to find the limit switch stroke? Is it a physical switch?

    Thank you all for your help
    Do not laugh at my English

  2. #2
    Join Date
    Mar 2012
    Location
    Portland OR
    Posts
    9
    Thanks
    0
    Thanked 2 Times in 2 Posts

    Default Re: Need Help [Amada Fanuc AMADAN 04-PC] Error 220 & 221

    Is this machine a "Wet Clutch" machine?
    This could be related to the oil pressure!
    Is your shop heated? This could also be related to oil tempature?

  3. #3
    Join Date
    Oct 2012
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Re: Need Help [Amada Fanuc AMADAN 04-PC] Error 220 & 221

    This machine is Pega 367th
    In the factory we have heating and a constant temperature of around 16 degrees Celsius.
    Sometimes the light is the oil filter error, but I did not notice due to my problem...but I could be wrong.
    I'll check it out

  4. #4
    Join Date
    Mar 2012
    Location
    Portland OR
    Posts
    9
    Thanks
    0
    Thanked 2 Times in 2 Posts

    Default Re: Need Help [Amada Fanuc AMADAN 04-PC] Error 220 & 221

    Have you ever replaced the filter? I usally let my machines idle for 15-30 minutes before punching. Also I sometimes run a warm up test program on a empty tool station. Give it a try!

  5. #5
    Join Date
    Oct 2012
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Re: Need Help [Amada Fanuc AMADAN 04-PC] Error 220 & 221

    Hello!
    Filter and oil were replaced in August 2011. From my observations show that the problem is not associated with oil pressure or a glass filter. I have to look any further

  6. #6
    Join Date
    Mar 2012
    Location
    Portland OR
    Posts
    9
    Thanks
    0
    Thanked 2 Times in 2 Posts

    Default Re: Need Help [Amada Fanuc AMADAN 04-PC] Error 220 & 221

    220- +Y-axis.& stroke limit switch has been actuated.
    221- -Y-axis & stroke limit switch has been actuated

    These limit switches may need to be "cleaned" or the rails/cams that actuates the switches may be out of adjustment.

    When you start program what is your first "X" and "Y" hit and what tool station did you call out for? Are you punching material or air? You can run on a empty tool station and no material to warm up machine!

  7. #7
    Join Date
    Mar 2012
    Location
    Portland OR
    Posts
    9
    Thanks
    0
    Thanked 2 Times in 2 Posts

    Default Re: Need Help [Amada Fanuc AMADAN 04-PC] Error 220 & 221

    220- +Y-axis.& stroke limit switch has been actuated.
    221- -Y-axis & stroke limit switch has been actuated

    These limit switches may need to be "cleaned" or the rails/cams that actuates the switches may be out of adjustment.

    When you start program what is your first "X" and "Y" hit and what tool station did you call out for? Are you punching material or air? You can run on a empty tool station and no material to warm up machine!

    Do you have a Operator's Manual for you machine? If you don't you can go on Amada's web site and down load a copy! It would be under - "Service-Product Documentation-Punching-Pega-Pega O4P wet" They will let you download it in PDF form.

Similar Threads

  1. amada pega 357 and fanuc
    By 0joze0 in forum Machine Repair & Troubleshooting
    Replies: 1
    Last Post: 10-02-15, 12:49 AM
  2. Amadan-04pc-c
    By mecho_greco in forum Machine Repair & Troubleshooting
    Replies: 1
    Last Post: 02-06-14, 11:25 AM
  3. AMADA HDS 8025 PRESS BREAK "error code 2236-Y2 axis sensor abnormal"
    By Blackwme in forum Machine Repair & Troubleshooting
    Replies: 0
    Last Post: 06-13-13, 11:03 AM
  4. Amada Error Code
    By JRCM in forum Fanuc Controls
    Replies: 1
    Last Post: 08-12-11, 01:00 PM
  5. manuals for amadan 04p-c fanuc controls
    By ROOFRON in forum Fanuc Controls
    Replies: 3
    Last Post: 08-16-10, 07:19 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •