Results 1 to 6 of 6

Thread: CNC 16i LADDER Programm

  1. #1
    Join Date
    Oct 2009
    Posts
    9
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default CNC 16i LADDER Programm

    Hello,
    I am searching the way for getting the LADDER of the Machine in order to improve some parameters of the configuration.
    I would like to work online with this machine, I mean I would like to see the programm while it is running. I think it is possible by the Embedded Ethernet option.
    So I have the FANUC LADDER III 4.6. But when I put my IP address there is no connection.
    Anyone knows about that?

    I hope your response,
    thank you very much,
    Alberto

  2. #2
    Join Date
    Oct 2007
    Posts
    82
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Re: CNC 16i LADDER Programm

    There's a parameter that you may have to adjust that says to use the ethernet port for ladder programming.

    Also if you haven't done so already you need to modify your Fanuc Ladder settings.

    I just bought a new desktop so I currently do not have access to everything yet so I will have to get back to you with any info I find.

  3. #3
    Join Date
    Oct 2007
    Posts
    82
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Re: CNC 16i LADDER Programm

    If you go to the "SETTING" screen and parameter 24 is 0 than you need to navigate to the
    "PMC online screen" and you have to put "HIGH SPEED" setting to "USE"

    Press -> SYSTEM -> PMC -> MONIT -> ONLINE

    You'll also have to manually enter IP addresses on the CNC controller as well as manually set your laptop to the same IP range. Obtain IP address automatically on your laptop will not work.

    You may need to use a "CROSSOVER" ethernet cable ... been awhile so not sure if a standard ethernet cable will work.

    There may be a PING feature on the CNC to see if there's any communication at all with your laptop
    and you can try to PING the CNC from your laptop as well.

  4. #4
    Join Date
    Oct 2009
    Posts
    9
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Re: CNC 16i LADDER Programm

    Mustang...
    Thank you very much. I could connect with the machine trought Ethernet. But something strange is happenning because I can receive a response when i send a ping from my computer, but when i use the ping of the machine that shows me DATA NICHT GEFUNDEN.
    Another, Do you know which is the routine or where are the information related to pressure, energy, or forces?.

    Thank you very much again,
    Alberto

  5. #5
    Join Date
    Sep 2005
    Location
    Wisconsin
    Posts
    996
    Thanks
    5
    Thanked 76 Times in 66 Posts

    Default Re: CNC 16i LADDER Programm

    Do you have a firewall enabled on your PC? Try turning it off. I had this working at one time but don't remember all the details.

  6. #6
    Join Date
    Oct 2009
    Posts
    9
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Default Re: CNC 16i LADDER Programm

    Petro CNC,
    Yes, the firewall of my computer is disable. It is strange, because I can work everytime, I haven't got problems with communications or something like that. I mean I can connect online with the PLC but the PING of the machine doesn't work.
    It still shows me DATA NICHT GEFUNDEN.

    Regards,
    Alberto

Similar Threads

  1. automation programm and dnc
    By deekayenggworks in forum Machine Repair & Troubleshooting
    Replies: 2
    Last Post: 01-30-10, 06:12 AM
  2. CNC 16i LADDER Programm
    By Albert in forum Automation & Interfacing / Installation / Ladder logic
    Replies: 2
    Last Post: 11-17-09, 02:12 AM
  3. CNC 16i LADDER Programm
    By Albert in forum Machine Repair & Troubleshooting
    Replies: 0
    Last Post: 10-28-09, 04:47 AM
  4. miyano bnc34t programm help
    By CHANDRU in forum Machine Repair & Troubleshooting
    Replies: 0
    Last Post: 09-04-09, 06:09 AM
  5. Fab Ladder iii
    By chad in forum Automation & Interfacing / Installation / Ladder logic
    Replies: 5
    Last Post: 08-14-08, 08:24 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •