Search:

Type: Posts; User: psharp1; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    2,196

    Re: MATSUURA MC-510VG ATC problem

    Not the Parm you need, You need to look for the ones that actually show the M Code. These are set by the manufacturer.
  2. Replies
    4
    Views
    2,196

    Re: MATSUURA MC-510VG ATC problem

    Yasnac made controls for many different machine manufactures. Each manufacture had the option of what codes they used for what. Many of these (for the same machine) were different depending on what...
  3. Replies
    4
    Views
    4,317

    Re: STAMA MC 320 FANUC OM

    Fanuc made controls for many different machine manufactures. Each manufacture had the option of what codes they used for what. Many of these (for the same machine) were different depending on what...
  4. Replies
    4
    Views
    2,129

    Re: Simple question. Not Ready Fanuc0M

    When you go past the limit switch like that the machine actually moves without the computer knowing it. Power it completely down and power it back up holding the "P" & "can" buttons in until powered...
  5. Replies
    1
    Views
    1,309

    Re: Sinumerik 810t reference points change

    Correct your tool offset. If it is obove or below center, that is a different problem.
  6. Thread: Btr

    by psharp1
    Replies
    5
    Views
    2,226

    Re: Btr

    Keep in mind, all null modems are not the same and may not all work.
  7. Thread: Btr

    by psharp1
    Replies
    5
    Views
    2,226

    Re: Btr

    Yes you have to use a null modem cable. For the 2000g it is usually 7, 2, E. Your setting in the machine will not normally be the same. You may have to try several combinations to get it to talk...
  8. Thread: Btr

    by psharp1
    Replies
    5
    Views
    2,226

    Re: Btr

    The only BTR (between the rail) units I have seen are cooling fans.
    However, you can hook up to the serial pin outs of the tape in/out. you can Upload & download that way.
  9. Replies
    3
    Views
    1,796

    Re: need help ikagai fanuc 6TB

    On a Fanuc 6 if you do not have an alarm and it does not start, something physically is not in start position. It could something simple like air not turned on.
  10. Replies
    11
    Views
    6,168

    Re: toyoda FA550 fanuc 15M control

    'M' codes are a machine side code that change a diagnostic bit from 0 to 1 or 1 to 0. These trip a relay or etc to make the machine respond to that action. If you look at your schematics for the 15M...
  11. Replies
    13
    Views
    6,969

    Re: need help moriseiki MV 45 fanuc 6m

    On a hydraulic ATC, you should be able to trip a solenoid to make the ATC move to position.
  12. Replies
    13
    Views
    6,969

    Re: need help moriseiki MV 45 fanuc 6m

    Check to see if all of your sensor lights are on "saying it is in the correct position". If they are not, you either are not in positon, one of your sensors are out, or a board is bad. Before you...
  13. Replies
    13
    Views
    6,969

    Re: need help moriseiki MV 45 fanuc 6m

    The motor has a mechanical brake on the motor. You have to release it to turn the motor thus turning the arm. The arm will go through all the motions it needs until it arrives at the correct...
  14. Replies
    13
    Views
    6,969

    Re: need help moriseiki MV 45 fanuc 6m

    With the machine powered down. To move it manually, you have to take the fan cover off the ATC motor. Depending on the motor, there may be a hex on the shaft to put a socket on to turn it with a...
  15. Replies
    13
    Views
    6,969

    Re: need help moriseiki MV 45 fanuc 6m

    If you are not set up with MDI individual movements of your carousel you might try changing the diagnostic bits to move to where it is in position. If this does not work, you will probably have to...
  16. Replies
    5
    Views
    2,525

    Re: Hitachi Seiki Model VA 40

    Most CNC MFG's have a repair shop for boards & and sometimes have used boards already repaired if you need the damaged boards repaired. Sometimes local board or online repair shops will do this. ...
  17. Replies
    5
    Views
    2,525

    Re: Hitachi Seiki Model VA 40

    Find the pinouts for the port. Most of them will have both serial and parallel pinouts. You can use either one of them to recieve or send as a tape.
  18. Replies
    5
    Views
    2,525

    Re: Hitachi Seiki Model VA 40

    This model had a setup for a tape drive. Is it in tact?
  19. Replies
    1
    Views
    1,364

    Re: I will have a trial for programming job

    Did they say that was the software they are using? If so it should have a built in tooling and material software for any particular material. Maybe not in the trial software.
  20. Replies
    1
    Views
    1,440

    Re: Personalization Fanuc

    In your case Fanuc is the manufacture of the software. If you wish, Fanuc sometimes will let a manufacture of the machine put their name there. If your software is a Microsoft version (GE Fanuc)...
  21. Thread: Fanuc problem?

    by psharp1
    Replies
    4
    Views
    2,116

    Re: Fanuc problem?

    That might rid you of the alarms but not the problems.
  22. Replies
    16
    Views
    5,382

    Re: HMC changeover custom macro headache

    That is sad. There are too many easy ways to have adjusted grid shift & positioning than to tie up such valuable variables.
  23. Replies
    16
    Views
    5,382

    Re: HMC changeover custom macro headache

    By the way, Some machine builders have decided to use the O8000's & O9000's for their own special macros and have locked them out. You might watch for that.
  24. Replies
    16
    Views
    5,382

    Re: HMC changeover custom macro headache

    Once you get the hang of it, writing a program is easier & quicker than doing a Cad Cam version. Saves a lot of space & time. Safer too. Wrote them so I could put them on any of the machines. I...
  25. Replies
    16
    Views
    5,382

    Re: Cracked it......I think

    I used it to monitor my QS 9000 data, maintenance, and tool life. I used them to in able complete set ups in 30 minutes. I had over 30 CNCs I had to use Macros to 'bullet Proof' because I hired temps...
Results 1 to 25 of 49
Page 1 of 2 1 2