Search:

Type: Posts; User: tushar; Keyword(s):

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    4,101

    Re: Need a Fanuc O-T series manual

    pl mail me your adress.what manuals are you looking for
  2. Re: kitamira with Funuc15-m tool changing arm stopped at spindle

    IN kitamura hmc machines a keeprelay has to be turned on. After this the mode selector switches such as single block / dry run etc can be used for arm movement of the atc.
  3. Replies
    2
    Views
    1,647

    Re: Alarm " J " on 11M Fanuc motherboard

    Thanks for the suggestions.
    All these things have already been checked & are working ok
  4. Replies
    0
    Views
    1,204

    Fanuc 11M control alarm "J"

    I have a Hitachi Seiki HMC H400. Fanuc 11M mother has a interminnent problem of alarm "J".Every time we have the alarm we remove the motherboard,clean it & put it back to use,the alarm disappears....
  5. Replies
    2
    Views
    1,647

    Alarm " J " on 11M Fanuc motherboard

    I have a hitachiseiki hmc h400.It has a interminnent problem of "J" alarm on mother board.Till date every time we have the alarm we remove the motherboard clean it & put it to use,the alram...
  6. Replies
    5
    Views
    5,481

    Re: Kitamura H400 HMC Pallet changing problem.

    Sir,
    We were able to reference the machine.But the data like pallet changing arm waiting position distance from reference point, forward position, backward position has to be set in data...
  7. Replies
    5
    Views
    5,481

    Re: Kitamura H400 HMC Pallet changing problem.

    We had to load all the PMC & NC parameters.Actually the pallet changer Arm is driven by a Fanuc servo motor.Three positions of the arm have to be defined.
    1.Front, 2.Back 3.Safe /waiting...
  8. Replies
    5
    Views
    5,481

    Kitamura H400 HMC Pallet changing problem.

    I recently brought a Kitamura H400 HMC with 15M control. During installation of the machine we had a alarm "RAM Parity error".To clear the same the memory had to be formatted.After reloading of the...
  9. Thread: Kit 400 problem

    by tushar
    Replies
    2
    Views
    2,334

    Re: Kit 400 problem

    Hello , I recently brought a Kitamura H400 hmc. with 15M control . But unfortunately all the data was lost. If you have a similar machine can you help me.
  10. Re: kitamira with Funuc15-m tool changing arm stopped at spindle

    What machine is it.
    There is a method in JOG mode using switches on panel board you can move the arm.
    Pl specify the machine model no so that I can help you
    Tushar
  11. Replies
    4
    Views
    2,532

    Re: Kira ATC tool change arm speed

    Try using a VFD drive to control the speed of the ATC motor.
  12. Replies
    3
    Views
    3,165

    Re: hitachi seiki hc400 data

    any one requiring data for hc 400 hmc mail me :-trgugale@gmail.com
  13. Replies
    4
    Views
    2,666

    Re: Parameters for colchester tornado 300

    I tried to contact them.No reply.
  14. Replies
    4
    Views
    2,666

    Parameters for colchester tornado 300

    Sir,
    Can somebody pl help me with Fanuc OTC parameters & dgn for colchester Tornado 300 CNC turning lathe.I do not have the manuals & my machine memory had to be cleared
    Regards
    Tushar
  15. Replies
    3
    Views
    3,165

    hitachi seiki hc400 data

    data for hitachi seiki hc400 data
  16. Replies
    7
    Views
    4,140

    Re: Hitachi Seiki-apc changing for hc 400 hmc

    Thanks Stevo
    Its Working.
    One more thing , can you suggest how to take backup of Hitachi seiki Plc
  17. Replies
    7
    Views
    4,140

    Re: Hitachi Seiki-apc changing for hc 400 hmc

    thanks stevo.
    I donot have paramater 4120 on my machine. Only paramaters upto 2506 are visible. After that directly paramater 4821 is visible. Pl help.Can you help me in writing a macro & defining...
  18. Replies
    7
    Views
    4,140

    Re: Hitachi Seiki-apc changing for hc 400 hmc

    Thanks for the reply.
    The PLC is micron & I am not sure about its interfacing with fanuc.
    Pl help
  19. Replies
    7
    Views
    4,140

    Re: Hitachi Seiki-apc changing for hc 400 hmc

    thanks steve .
    The control is Fanuc 11 M & Micron 16-2 PLC
    There was a problem with parameter setting.
    Type of pallet changer used was not selected properly.
    There is one more problem.If the...
  20. Replies
    7
    Views
    4,140

    Hitachi Seiki-apc changing for hc 400 hmc

    There is a problem with my machine.I am not able to do the pallet changing.Donot have the macro program.Pl help
Results 1 to 20 of 20