Search:

Type: Posts; User: Petro; Keyword(s):

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    1,270

    Re: Anilam 1400m security device

    Not to familiar with that control. However a power sounds like a good possiblility. At power on is a common symptom. Leave it on to warm everything up restart the machine and if works most likely the...
  2. Re: OKK MCH-600, Fanuc 16M: 309 APC Alarm : B axis ZRN IMPOSSIBL

    Glad you were able to get this going and thanks for posting how you resolved this issue. Cheers!!
  3. Re: OKK MCH-600, Fanuc 16M: 309 APC Alarm : B axis ZRN IMPOSSIBL

    Sanssp,
    First I would check that the pallet changer is in proper position to move the B axis. Also make sure pallet is at a clamped state. Then a lot of manufactures have a special bit or procedure...
  4. Replies
    15
    Views
    13,374

    Re: Windows based CNC controls

    That is a one of a kind machine I am sure. Anytime someone says router and CNC together usually had very few sold. I have never even heard of a AMC-4 controller. I am guessing it has a windows front...
  5. Re: How long does it take for a post to be approved by mods?

    Sorry Jamie, not sure what was in your thread that would have flagged a spam filter of some kind. I will take a look at it now. Unfortunitly I am the only mod at the moment and am very busy to try to...
  6. Replies
    1
    Views
    2,180

    Re: Fanuc 15 M, on Niigata HN50B

    I think your only option on this control is to integrate a device that records this. Often you can tie it into a stack light signal tower. Green light for run. Orange light for how many cycles are...
  7. Replies
    1
    Views
    2,334

    Re: Mori Seiki TL40 Fanuc10TF Tool setter problem

    Do you have the ladder book on this machine? If so there is a list of Keep relays and D bits in the back. Read through all of them and see if anything makes sense to enable the presetter and steady...
  8. Thread: MillPWR Help

    by Petro
    Replies
    5
    Views
    5,616

    Re: MillPWR Help

    Not Familiar with that particular control. But battery would be plausible since the machine has been powered down for some time. Best bet I think on this one is to call the manufacturer. Looks like a...
  9. Replies
    2
    Views
    3,216

    Re: Johnford SL-800B False overtravel

    Bob,
    Usually when there is a problem with the machine the hydraulics often turn off. I would check the drives for alarms on them when it stops. If there is something displayed that will help...
  10. Replies
    1
    Views
    2,879

    Re: Daewoo puma 10S2T with fanuc15TT pmc parameter

    First thought would be to contact Daewoo for basic defaults. Otherwise someone here may have a backup that might get you close.
  11. Replies
    22
    Views
    12,675

    Re: Change language in SeicosMkII (Hitachi VK45II)

    Sorry cannot find anything other then what you have above.
  12. Re: 1988 HITACHI SEIKI Model HTC 25S Lathe Alarm 512 Spindle Start Impossible

    They have a slip coupling on one of the ballscrew axes. You must re-engage and then the alarm will go away.
  13. Replies
    1
    Views
    1,729

    Re: Hitting hard stop during a zero return

    Try changing the gridshift parameter to zero power down then back up and see if it zero returns properly. Its probably counting the grdishift to far if you did see the switch turn off after it came...
  14. Re: Hitachi-Seki 4NE-600 Turret Alignment - Which bolts?

    Best bet would be to find a cross section view of the turret. Many times there is an inner coupling as well as outer coupling that can shift. Not sure if this machine has that. But those pins you may...
  15. Replies
    3
    Views
    2,443

    Re: Mazac spindle problem

    I am not a programmer, but I believe you are correct, however are there some sync codes in the programs as well where it waits for other functions to be done in opposite program before continuing?
  16. Re: 4th axis onto a Cincinnati Millacron Arrow 500 CNC with Acromatic 2100 control

    If its an indexer type interface with its own seperate controller you might be able to do easy by external mcodes. However if its a fully integrated 4th that I don't have a clue, but the odds are you...
  17. Replies
    4
    Views
    2,988

    Re: Hitachi Seiki VS50 with 16i-MA

    Eric,
    Sorry to here that. Never encountered someone blowing that part of the memory out. My best guess would be to either find someone with similar machine like you are trying to do or contact Mori...
  18. Thread: Amadan-04pc-c

    by Petro
    Replies
    1
    Views
    2,286

    Re: Amadan-04pc-c

    Do you have a 25 pin RS232 Port? If so you probably need to transfer via RS232 back and forth programs. Here is all the RS232 hardware and software you may need. They also provide tech support for...
  19. Replies
    1
    Views
    1,253

    Re: Devective tool in main axis (error 02A91)

    WHen does error come up?
    WHen you command axis to move?
    When you call for a tool change?
    Is there a tool in the spindle?
    What was the last thing the machine did before this alarm occured?
  20. Thread: Hydraulic leak

    by Petro
    Replies
    1
    Views
    2,066

    Re: Hydraulic leak

    Typically this is coming from the actuator. There are some drainage pans typically in the back that can sometimes get clogged and the oil then backs up into the drawtube. Make sure none of the hoses...
  21. Replies
    6
    Views
    5,039

    Re: USB to Serial Card - Are you sure that's the conversion you need?

    If your just looking to transfer programs into the control and not drip feed to the control you should be able to get away with a USB to Serial adapter. If you need to drip feed a desktop with a true...
  22. Thread: reference return

    by Petro
    Replies
    1
    Views
    1,563

    Re: reference return

    Sorry that does that for safety until you zero return it. Its made to go that speed to protect you machine incase something is wrong with the physical switches that tell the machine where home...
  23. Thread: lgotts

    by Petro
    Replies
    1
    Views
    1,437

    Re: lgotts

    I checked my 6M manual and I do not see the alarm number 437 sorry. Are you sure that was the alarm code?
  24. Thread: conquest t64

    by Petro
    Replies
    1
    Views
    1,473

    Re: conquest t64

    Could be a few things. Interlock from tool changer or pallet changer if the machine has. Could also be that the work envelop is not set properly for some reason. If you want to move in the other...
  25. Thread: Matsuura RA-2F

    by Petro
    Replies
    1
    Views
    2,758

    Re: Matsuura RA-2F

    I'd be curious on this one. I did it once but cannot remember. There is some values I thought had to match in the ladder as well otherwise it would just sit there. You can start by changing the...
Results 1 to 25 of 300
Page 1 of 12 1 2 3 4