Search:

Type: Posts; User: Gridley51; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    2,494

    Re: 810 GA3 M Communications bits

    I posted the settings a few days ago on this thread here.

    http://cnc-professional-forum.com/machine-repair-troubleshooting/5072-sinumerik-810t-ga3.html#post19473
  2. Replies
    4
    Views
    2,675

    Re: Tool problem on 810

    I didn`t mean something wrong with the way you load it,but,possibly an unrecorded mod was made to the plc programme after the backup had been done.
    If you look at the 810 manuals you will see that...
  3. Replies
    4
    Views
    2,675

    Re: Tool problem on 810

    See if you can find the manuals for the 810 from Siemens website which is called doconweb.
    I think though that this will be something in the plc programme so you may need to look at that.If you have...
  4. Replies
    21
    Views
    11,037

    Re: Sinumerik 810T GA3

    You need to change the eprom.The control as you know comes with two languages.The standard first is English,other languages are option.The second language is always German.
    ISTR it`s one of the...
  5. Replies
    21
    Views
    11,037

    Re: Sinumerik 810T GA3

    Clayton,I have already PM`d you this but will paste it here for others.
    It is for a GA1 but I think it`s the same but can check.
    These parameters have to be set manually prior to loading the other...
  6. Replies
    21
    Views
    11,037

    Re: Sinumerik 810T GA3

    Forgot all about this.

    No it`s not a problem.Comms parameters have to be set manually then you need to load things in a certain order.Bit of messing about the first time you do it but obviously...
  7. Replies
    21
    Views
    11,037

    Re: Sinumerik 810T GA3

    You have to manually set some parameters before you can upload the files.I don`t have the info here but will post it tomorrow if nobody else steps in.
    How to do this has been posted on this forum...
  8. Replies
    3
    Views
    2,984

    Re: CNC Sinumerik Language problem

    You will need to do a complete reload of everything including the plc programme.Do you have a backup of anything?
    I have had this same problem with an 820 control.Batteries went flat within 24 hrs.
  9. Replies
    4
    Views
    1,778

    Re: Wanted Ge HiAk spindle drive

    If you could unpot that you would probably find nothing special but no way of identifying the components either.
    Who have you tried?
    Hartel says they have them but you would need to ask the price....
  10. Replies
    4
    Views
    1,778

    Re: Wanted Ge HiAk spindle drive

    Why not repair the Hiak.They are dead simple to work on.
    Failing that call up Control Techniques and ask if they have any Mentor 11`s left.They stopped making them but had a few in stock which were...
  11. Replies
    3
    Views
    1,627

    Re: matrix churchill help me

    These people should be able to supply what you need.

    http://www.bsamachinetools.com/Machine%20Spares.htm
  12. Replies
    11
    Views
    2,805

    Re: Beaver NC25 need electrical drawings

    Have you tried Mark Mallinder at Servotek.He`s ex head of service at Beaver and has most things electrical for them.
    http://www.servotek.co.uk/
  13. Replies
    8
    Views
    4,780

    Re: Backup SINUMERIK 810M GA3

    What machine have you got?
  14. Replies
    3
    Views
    2,503

    Re: CNC Punch Help Please?

    You should have told Mr Stewart not to buy the cheapest punch he could find. :D
  15. Replies
    1
    Views
    1,128

    Re: electrospindel problems

    The sensor which can be a limit switch or proximity switch or the wiring to it which tells the control the tool is in position is faulty.
    The control thinks the tool is in position and sends the...
  16. Replies
    7
    Views
    8,361

    Re: Mitsubishi Manuals

    You end up with that site if you are in Europe,possibly anywhere outside N America.
    The trick is to go into control panel on your computer and change your time zone setting to a N American one then...
  17. Replies
    3
    Views
    1,717

    Re: 2153 Control loop spindle - HW

    Sounds like spindle encoder is faulty.
    Explanation is:-
    The measuring circuit differential circuits.....
    Are not in phase
    Have a short to earth
    Are missing
    Effect of this is to inhibit NC start.
  18. Replies
    5
    Views
    3,845

    Re: GE Mark Century 2000

    I think you can get the MSD up on the screen without the support board.I can`t remember as it`s that long since I`ve done it.
    Where you may have problems is I seem to remember that there are...
  19. Replies
    1
    Views
    2,204

    Re: Siemens Sinumerik 3T

    Try John Leighton at www.johnleightoncncservices.co.uk
  20. Replies
    0
    Views
    1,122

    Siemens 6SC610 drive

    Has anyone been successful at repairing the stack/amplifier cards from these drives?
    Info on the repair of the GO cards would be gratefully received too.
    Mark.
  21. Replies
    7
    Views
    2,507

    Re: Ooya spindle trouble

    Sorry,misunderstood you.
    The process is quite simple.
    Dismantle and clean thoroughly.Some people pressure wash the components but you then need to cook it in the oven until it is 100% dry.
    Skim...
  22. Replies
    7
    Views
    2,507

    Re: Ooya spindle trouble

    I`m not running you down,but when you have to ask,I would say it would be better if you took it to a motor shop.
    I do my own because I was taught how to do them when I was an apprentice.
  23. Replies
    7
    Views
    2,507

    Re: Ooya spindle trouble

    I totally agree.OP has been lucky he has not taken the drive out.
    I was standing next to a 80hp motor when it flashed over,very frightening.
    A comm skim,brushes,bearings and a clean cured that one....
  24. Replies
    0
    Views
    1,352

    Anilam Crusader ML control

    Has anyone got any info on the above control as fitted to an Avon lathe.
    I have been asked to look at a non working machine which is quite a distance away and have no experience of them as I`ve...
  25. Replies
    12
    Views
    5,214

    Re: Sinumerik 810T GA1

    I`m familiar with the Seal Jet operation.I was actually just asking about them the other week.
    If you drop me an email I`ll send you the procedure for matching the boards and motors with the...
Results 1 to 25 of 36
Page 1 of 2 1 2