Search:

Type: Posts; User: bill4807; Keyword(s):

Search: Search took 0.07 seconds.

  1. Thread: FladderIII

    by bill4807
    Replies
    2
    Views
    5,471

    Re: FladderIII

    Hi Codyst,
    Thank you for your reply. I was skimming this website and saw my own post. lol. I must have forgotten and not have checked back after I posted it. I know there are not alot of PMC...
  2. Replies
    11
    Views
    6,136

    Re: toyoda FA550 fanuc 15M control

    Stevo:

    You are correct..I was wondering why I could not pull the ladder up on Fladder III. This is weird since I believe the PMC-N is supported by FladderIII. Do you know why? I tried saving to...
  3. Replies
    11
    Views
    6,136

    Re: toyoda FA550 fanuc 15M control

    Hi! thanks. Yes I did find a end of program buzzer relay that is hooked in the ladder to the M30 and M02.

    I found out I cannot even pull the PMC ladder up on my Fladder software since this...
  4. Thread: FladderIII

    by bill4807
    Replies
    2
    Views
    5,471

    FladderIII

    does anybody know how to properly use a DECB function so that I can decode an M30 Function?

    I have a programming book that explains the DECB function and I hooked it up loaded into the CNC but it...
  5. Replies
    11
    Views
    6,136

    Re: toyoda FA550 fanuc 15M control

    thanks for the info!

    I was thinking about maybe putting a Y output in parallel with whatever internal relay the Decode function for (M30) was. Do you think this would work?

    I do have some...
  6. Replies
    11
    Views
    6,136

    toyoda FA550 fanuc 15M control

    Wanting to add an external parts counter..has anybody ever integrated one into a fanuc control. I know there is an internal parts counter too. Can you just maybe take the M30 command and create a...
  7. Replies
    5
    Views
    2,656

    Re: fanuc A20B 2001 0931 07B

    Indygreg, is right these multilayer board s are hard to repair, but really the only issues i see with these are either the power supply section goes/which isnt your case since ur display works still...
  8. Replies
    0
    Views
    1,571

    fanuc 15-M model A?

    Is a "15M" a model A controller?

    Does anybody know if there is another area/port on another circuit board to connect the DNC communication 232 cable other than the 01p1e board? my problem is I do...
  9. Replies
    4
    Views
    2,938

    Re: fanuc 15-MA/makino

    OK thanks! I think i may change the I/O board. Since it is still happening once or twice a day.
  10. Replies
    4
    Views
    2,938

    Re: fanuc 15-MA/makino

    thanks for replying Bill!
    Pinout is:

    DB25 side: DB9 side:

    6-8-20
    4-5
    2 ----------------2
    3 ----------------3
    7 ----------------5
  11. Replies
    4
    Views
    2,938

    fanuc 15-MA/makino

    Hi!

    I am having an issue here with getting a "SR821 CD OFF (1) fault" intermittently. It happens maybe once every 2 hours.

    I replaced the rs-232 cable already. Checked all the comms parameters...
  12. Replies
    2
    Views
    2,164

    Re: Mori Seiki University - Education On Demand

    Will these classes help with alarm issues, and how to solve or do you think you would have to go to the controller manufacture to get trained on that?
  13. Replies
    2
    Views
    4,518

    Re: ABSO POS CHECK ERROR

    Did your power supply on the computer rack fail previous to this error?

    Is interlock for X axis set to (1)?

    There is a procedure to clear this fault.
Results 1 to 13 of 13