Search:

Type: Posts; User: alexfanuc; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: FANUC 180i

    by alexfanuc
    Replies
    5
    Views
    5,804

    Re: FANUC 180i

    Hello:

    Do you still have this machine Moriseiki MSG501?
    I am trying to get the PMCCIA image.

    Regards


    AlexFANUC
  2. Re: Mori Mapps PCMCIA(compact flash) format to reload Mapps unit

    Hello Petro,

    Did you ever solve this problem?

    I am trying now to fix a problem like that.
    The ATA seems to have a problem.
    regards


    AlexFANUC
  3. Re: Ram Parity Error 18T control on Hardinge T51

    Hello:
    Could you just input paramaters 9900 , one by one, power off and on and tell me when the alarm happens?

    Regards

    AlexFANUC
  4. Replies
    1
    Views
    5,659

    Re: What does mean OI-TD in fanuc oi control?

    Oi TD= 0 is zero. It is the series of the control. i it is also the series.
    T = Turning (Lathe)
    The 0i control has several types . A, B , C D. In this case we have the D control. They have some...
  5. Replies
    3
    Views
    2,035

    Re: Home going wrong direction.

    Hello:
    First of all, was the machine working fine? When you say, it homes to the wrong direction, does the axis stop in the opposite direction?
    Did you change parameter 1815? Do you know the value...
  6. Replies
    1
    Views
    1,430

    Re: Daewoo Fanuc rom parity error 998 122C6

    What is the part number of the PCb where this chip is located?
    Regards
    Alex
  7. Replies
    4
    Views
    2,806

    Re: Hardinge CHNC 2 RAM TEST

    Do you have a backup of the parameters?
    I think you must erase memory. What´s the master pcb part number? Does it have a battery? If you do, you will find a black connector near the led display on...
  8. Replies
    12
    Views
    11,375

    Re: 417 alarm on fanuc 6m-b

    What is your machine name? Model? Control number? Is it really a OM control?
    Regards
    Alex
  9. Replies
    2
    Views
    2,496

    Re: star sr32 fanuc 16-t

    The control needs to "know" that the motor is rotating. Can you move the motor? If you can, then try to move it away (JOG) from the reference point then move it back to about 3mm from it. From there...
  10. Replies
    3
    Views
    4,129

    Re: ALARM SV 323 B disconnect by soft

    Also, check if you have a scale.
    Regards
    Alex
  11. Replies
    5
    Views
    2,138

    Re: How to substitute C-series to Alfa-series

    I would say that you have a mechanical problem. If the load would remain the same (60%) then it is a electrical problem.
    It would be too expensive to switch to alpha motors just to find out that you...
  12. Replies
    17
    Views
    17,578

    Re: fanuc OM - parameters

    You need to input 900-920 by hand first.
    Power off and on the machine. If you have a computer you can upload all the parameters. If you don´t, then the only way is to input them by hand.
    Regards...
  13. Replies
    7
    Views
    4,700

    Re: Fanuc 6MB - Can't set parameters - Help

    Hello:
    You need parameters for what type of machine? Remember, each machine has its own parameters. Do you also have a Okada VMC machine?
    Regards
    Alex
  14. Re: fanuc 11 "L" error and masterboards revisions

    Because I was thinking you could replace this IC cheap easily, but if you are not sure this chip is the problem then it is not worth to try and swap it with the other PCB. This master pcb is too...
  15. Re: fanuc 11 "L" error and masterboards revisions

    Is this big IC soldered to the master PCB?
    Regards
    Alex
  16. Re: fanuc 11 "L" error and masterboards revisions

    I would put back the original pcb to see if the "L" appears again.
    Regards
    Alex
  17. Re: fanuc 11 "L" error and masterboards revisions

    Both PC boards are the same.Do not worry about that number.
    Do you have a back up of the memory? Where did you get the new Master PCB? Do you know it is a good PCB? Did you put back the old master...
  18. Replies
    2
    Views
    2,457

    Re: Fanuc 31i DNC operation (REMOTE)

    You need to change parameter 20 to a zero.
    Regards
    Alex
  19. Replies
    9
    Views
    4,291

    Re: operator message 2041 please set D304.5

    Hello,
    Did you enter the PMC parameters? To see these "parameters" you must push the parameter key twice. You will see "diagnostics" on top of the screen. The parameters you must enter are from 300...
  20. Thread: Fauc 10t

    by alexfanuc
    Replies
    5
    Views
    2,263

    Re: Fauc 10t

    Yes, this power supply is located near the monitor.
    Glad you solved your problem.
  21. Re: okuma act-2sp with Fanuc 0T alarm messages are not being displayed

    It depends on how the ladder was written. Sometimes the alarm on the panel will indicated just that, an alarm. In that case the machine manual not the FANUC manual should indicate what the problem...
  22. Re: okuma act-2sp with Fanuc 0T alarm messages are not being displayed

    Please check diagnostics 300 thru 600. Compare them if you have them written in a book. These are the parameters of the machine. The messages are written in the ladder. I am not sure why you are not...
  23. Thread: Fauc 10t

    by alexfanuc
    Replies
    5
    Views
    2,263

    Re: Fanuc 10t

    If the system is hanging up, you probably have a bad master pcb.
    First of all, you need to make a backup of the memory. Be sure to write down all the PC parameters. Red led on means you have a...
  24. Re: okuma act-2sp with Fanuc 0T alarm messages are not being displayed

    Is the machine working?
    Do you have all the original parameters?
    Regards
    Alex
  25. Replies
    6
    Views
    10,780

    Re:THIS IS SPAM!!!

    this is spam!
Results 1 to 25 of 79
Page 1 of 4 1 2 3 4