Search:

Type: Posts; User: camsys; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.03 seconds.

  1. Replies
    1
    Views
    1,832

    Re: 9.atc not ready medals64s

    These types of alarms are machine side alarms, which means that they come from the
    PLC ladder. They do not have anything to do with the Mits controller.

    There is most likely a sensor(s) that...
  2. Replies
    1
    Views
    2,059

    Re: Meldas 64 - contour smoothing issues

    M64 does have the HS/HA machining commands, but some OEM's required them to be purchased as options.

    G05.1Q1 HS/HA Control I
    or
    G05P10000 Hs/Ha Control II
    THis control also has the Super...
  3. Replies
    1
    Views
    3,321

    Re: Mitsubishi meldas 500 alarm

    THis is definetly an alarm being thrown by the PLC. OEM's write the PLC
    ladders for their machine.

    Did the alarm just appear, or was something changed recently?

    Even though there's no...
  4. Replies
    1
    Views
    1,688

    Re: MITSUBISHI model 70-700 controler

    What is it that you would like feedback on?

    Sorry to hear that the boss is sorry for getting the controller that
    came with the retro fit.

    Mits 70 and 700 series are excellent controllers...
  5. Thread: M Codes

    by camsys
    Replies
    1
    Views
    2,336

    Re: M Codes

    I have a sheet for SL series that may be close:

    M25 tailstock spindle out
    M26 tailstock spindle in
    M392 "tailstock positioning to connection position"
  6. Re: Help with Denford Micromill? Completely new to CNC!

    I dont know about the denford in particular, but as far as your G-code
    question goes here's a few thoughts......

    The machine will most likely have a controller software that interacts with,
    and...
  7. Replies
    9
    Views
    2,715

    Re: need help with everything pc to machine

    angelw....

    Thanks for the clarification, my mistype is duly noted.
    Oddly enough I knew 2 and 3 get crossed, but in the throws
    of typing a reply typed it in worng despite!!!

    Sorry , but I...
  8. Replies
    9
    Views
    2,715

    Re: need help with everything pc to machine

    RS-232 communications requires a fair bit configuration on both the Fanuc and your PC.

    First off you will need to ensure that you have a correct cable with
    the proper pin-outs. I.E. Rs232...
  9. Replies
    2
    Views
    1,488

    Re: Ever run into this?

    If you are using notepad to originate the program, and you can't the
    program into the machine try changing the encoding to Unicode.

    New versions of notepad default to ANSI, and this seems
    to...
  10. Replies
    1
    Views
    3,419

    Re: mitsubishi meldas 500M seris controller

    You might want to check if there's a tool change macro being run
    in the place of the M06.

    I've seen this on mighty machines, the M500 allows a user
    to create a tool change maco that gets...
  11. Replies
    6
    Views
    8,194

    Re: Err m01 , 0057 WAIT FOR TAP RETRACT

    If you have an M70, then you can go to the DIAGN hard key
    and then PLC I/F softkey.

    Then you can set YC5C to 1 and follow the steps outlined in the earlier post.

    You can download the M70/700...
  12. Replies
    6
    Views
    8,194

    Re: Err m01 , 0057 WAIT FOR TAP RETRACT

    This can be corrected, but the solution varies by controller series.

    Lacking that information, we can still sort out the cause....

    Your Axies are interlocked; this happens when the tap cycle...
  13. Replies
    2
    Views
    1,595

    Re: Youji 1200 vertical turning center

    If you have a driven tool, then I assume that there is a Y axis present.
    Regardless of the Y, you should be able to interpolate on other planes.
    I don't know the exact Fanuc codes, but to work on...
  14. Re: Need Help - Takumi MCV 1100 - Meldas 500 - Not Run - Operation Status (ST1) EMG

    You might first verify if X24A, or Y29F, or X27 are ON,
    these are the outputs for E-stop Y29F is the PLC Estop.

    You could then get the Mitsubishi PLC interface manual for the
    M520 and check...
  15. Replies
    4
    Views
    4,356

    Re: Meldas 320L X&Z Axis not moving

    The problem is definitely in the PLC.

    Refer to the relevant manual, and look at the outputs for machine lock.
    my guess is that they are on.

    Outside of the test mode, or cable problem, I can...
  16. Replies
    1
    Views
    2,129

    Re: G74 on Mazatrol Smart

    By default G74 command requires 2 lines to initialize it.
    This is settable by parameter, but thry this format....


    N44G74R.1 The R value is the Retract amount in Z
    N45 G74 X[#506+.1]...
  17. Thread: Ethernet M70

    by camsys
    Replies
    3
    Views
    4,437

    Re: Ethernet M70

    The Mits M70 does not support DHCP, You must assign a static IP address.

    You can find the MAC address if you have a network sniffer.
  18. Replies
    1
    Views
    2,218

    Re: How to set up the system parameter?

    To enter machine parametrs Mit M0:

    ALM/DGN hard key
    Page FWD key 5 times to get soft key P6 sequence I/F

    Then H(1001) Data (1) Mode (M))

    Pressing parameter key will now display Machine...
  19. Replies
    4
    Views
    4,356

    Re: Meldas 320L X&Z Axis not moving

    Did the machine simply stop working, or were the
    parameters lost and restored?

    If you are using the manual modes (jog, handle, etc...) and
    the counters are updating with no alarms, then it...
  20. Replies
    5
    Views
    3,584

    Re: CNC Machine Crash

    Drug Test!!!! That's spot on!

    Human error, this is exactly where I was going with my previous comments, in that the "root causes" are in my mind overwhelmingly
    skewed to this prominent factor....
  21. Replies
    5
    Views
    3,584

    Re: CNC Machine Crash

    I'd be curious about the data you're using for your analysis.....

    Are you studying cases accross multiple sites, or simply within
    a single site. What methods are you using to analyse your data,...
  22. Re: logic to calculate time between spindle on off

    If you time is in whole numbers you parse off the 3 time components
    and convert them to decimal.

    For example if you want to subtract 09:45:30 from 13:30:30 I would
    suggest ignoring the seconds...
  23. Re: logic to calculate time between spindle on off

    I use Mitsubishi CNC controllers, but I believe Fanuc has the same capabilities.

    If you turn the spindle on/off with M03/M05 I might create an
    M03 user macro that writes #3011 and #3012 into...
  24. Replies
    4
    Views
    2,936

    Re: Backlash tolerance on NL-3000

    The parameters 2011 and 2012 are indeed used to compensate for backlash.

    The entry is an actual distace in fractions of a mm depending on what your 1003
    parameter is set to (B=1 micro Mill C=.01...
  25. Re: CNC Lathe Setup and Programming. Really need some Help!

    Hello,

    It sounds like you're facing a couple of learning challenges-
    1 - Basic CNC machine tool setup and operation
    2 - Basic CNC programming

    Where are you located? In the US ?

    I ask...
Results 1 to 25 of 43
Page 1 of 2 1 2