Not to familiar with that control. However a power sounds like a good possiblility. At power on is a common symptom. Leave it on to warm everything up restart the machine and if works most likely the...
Type: Posts; User: Petro; Keyword(s):
Not to familiar with that control. However a power sounds like a good possiblility. At power on is a common symptom. Leave it on to warm everything up restart the machine and if works most likely the...
Glad you were able to get this going and thanks for posting how you resolved this issue. Cheers!!
Sanssp,
First I would check that the pallet changer is in proper position to move the B axis. Also make sure pallet is at a clamped state. Then a lot of manufactures have a special bit or procedure...
That is a one of a kind machine I am sure. Anytime someone says router and CNC together usually had very few sold. I have never even heard of a AMC-4 controller. I am guessing it has a windows front...
Sorry Jamie, not sure what was in your thread that would have flagged a spam filter of some kind. I will take a look at it now. Unfortunitly I am the only mod at the moment and am very busy to try to...
I think your only option on this control is to integrate a device that records this. Often you can tie it into a stack light signal tower. Green light for run. Orange light for how many cycles are...
Do you have the ladder book on this machine? If so there is a list of Keep relays and D bits in the back. Read through all of them and see if anything makes sense to enable the presetter and steady...
Not Familiar with that particular control. But battery would be plausible since the machine has been powered down for some time. Best bet I think on this one is to call the manufacturer. Looks like a...
Bob,
Usually when there is a problem with the machine the hydraulics often turn off. I would check the drives for alarms on them when it stops. If there is something displayed that will help...
First thought would be to contact Daewoo for basic defaults. Otherwise someone here may have a backup that might get you close.
Sorry cannot find anything other then what you have above.
They have a slip coupling on one of the ballscrew axes. You must re-engage and then the alarm will go away.
Try changing the gridshift parameter to zero power down then back up and see if it zero returns properly. Its probably counting the grdishift to far if you did see the switch turn off after it came...
Best bet would be to find a cross section view of the turret. Many times there is an inner coupling as well as outer coupling that can shift. Not sure if this machine has that. But those pins you may...
I am not a programmer, but I believe you are correct, however are there some sync codes in the programs as well where it waits for other functions to be done in opposite program before continuing?
If its an indexer type interface with its own seperate controller you might be able to do easy by external mcodes. However if its a fully integrated 4th that I don't have a clue, but the odds are you...
Eric,
Sorry to here that. Never encountered someone blowing that part of the memory out. My best guess would be to either find someone with similar machine like you are trying to do or contact Mori...
Do you have a 25 pin RS232 Port? If so you probably need to transfer via RS232 back and forth programs. Here is all the RS232 hardware and software you may need. They also provide tech support for...
WHen does error come up?
WHen you command axis to move?
When you call for a tool change?
Is there a tool in the spindle?
What was the last thing the machine did before this alarm occured?
Typically this is coming from the actuator. There are some drainage pans typically in the back that can sometimes get clogged and the oil then backs up into the drawtube. Make sure none of the hoses...
If your just looking to transfer programs into the control and not drip feed to the control you should be able to get away with a USB to Serial adapter. If you need to drip feed a desktop with a true...
Sorry that does that for safety until you zero return it. Its made to go that speed to protect you machine incase something is wrong with the physical switches that tell the machine where home...
I checked my 6M manual and I do not see the alarm number 437 sorry. Are you sure that was the alarm code?
Could be a few things. Interlock from tool changer or pallet changer if the machine has. Could also be that the work envelop is not set properly for some reason. If you want to move in the other...
I'd be curious on this one. I did it once but cannot remember. There is some values I thought had to match in the ladder as well otherwise it would just sit there. You can start by changing the...