Search:

Type: Posts; User: Intertec; Keyword(s):

Search: Search took 0.04 seconds.

  1. Heidenhain Rotary Scale RCN 223 16384 Line Count Fits Makino 4th Axis Pro 5 Cont.

    Good working Heidenhain rotary scale. Came from Makino a61 4th axis table. Selling because pin in connector was broken after a table rebuild and customer did not want to wait for a replacement...
  2. Re: A61 Makino Pro 5 control how to download tool offsets

    assuming your using Makino Tool Data and M56 in 9001 program

    Is your I/O device set to 4 on the fanuc. Offset/Setting Key until setting screen comes up. MDI on the manual panel cursor to I/O...
  3. Replies
    1
    Views
    4,232

    Re: Daikin oil cooling unit Alarm E80

    When posting problems on this site you should mention what model number you have for the oil chiller or any other piece of machinery. Since there are a vast array of these chillers out there your...
  4. Replies
    6
    Views
    4,463

    Re: HELP WANTED...MAKINO 55e ALARMS!!!!

    I know this response is a bit late, but I was not aware of this site at the time of this posting. The through spindle rotary union is most likely at fault for the coolant in the spindle oil, which is...
  5. Replies
    1
    Views
    2,093

    Re: How does Fadal sense spindle speed?

    The CNC 88 controlled Fadals have an encoder mounted to the spindle motor. The fan shroud and cover needs to be removed to acccess the encoder. The encoder feeds back to the Baldor drive. Depending...
  6. Replies
    1
    Views
    2,110

    Re: Makino VMC SF64-A5

    What is a SF64 A5? Did you mean SNC64 with a 5th axis?
  7. Replies
    3
    Views
    2,706

    Re: Le blonde Makino FNC 74-A tool data error

    On older Makino machines with the c-mos board that has problems with tool mag, or tool restore programs, you should clear c-mos and then run the m57 tool load program
    You may have to remove the...
  8. Replies
    11
    Views
    6,247

    Re: Fancu orientation board

    Glad you got it back into service.
  9. Replies
    11
    Views
    6,247

    Re: Fancu orientation board

    The problem is not located in the incoming voltage to the main breaker, the problem lies in between the wires coming off the bottom of the spindle drive which go to a contactor(s) then from the...
  10. Replies
    11
    Views
    6,247

    Re: Fancu orientation board

    Sounds like you have lost one of the three phase legs, either through the motor cables going to the contactors or in the contactors themselfs. Pull the covers off the contactors and inspect the...
  11. Replies
    9
    Views
    4,433

    Re: Makino a61 loses hydraulic oil

    If your losing that much, your coolant will be greatly contaminated. The best way to find out what table build you have is call Makino at 1-888-625-4664 they have your S/N and model ready. Hit *#...
  12. Replies
    9
    Views
    4,433

    Re: Makino a61 loses hydraulic oil

    What years are the machines? This can be found on the white tag around the disconnect ex; 07-456, 07 beaing the year of manufacture. Are they Pro 5 machines? The reason I ask is that Makino for a...
  13. Replies
    4
    Views
    2,272

    Re: M19 spindle deaccelerates but does not stop

    Check the 3 phase at all points from spindle drive to motor leads. Sounds like that is the problem. Could be a broken wire in flexible duct. I've found that before when spindle stopping it will take...
  14. Thread: Apc alarm

    by Intertec
    Replies
    2
    Views
    4,461

    Re: Apc alarm

    I'm assuming this is a Fanuc 16 18 21 or 31 series control. With that in mind the simplest way to clear this alarm assuming there are no other problems is to reference the axis and hit Fanuc reset on...
  15. Replies
    10
    Views
    10,771

    Re: 12 alarms on Fanuc 18i-TB

    In looking at the 18i Fanuc manual the recommended coarse of action for that alarm 59 is to replace the Spindle drive and not the power supply. If you have a spindle drive that matches up I would try...
  16. Replies
    10
    Views
    10,771

    Re: 12 alarms on Fanuc 18i-TB

    So if you power up you can feel all the fans running on the amplifiers including the spindle amp and power supply? Those are the 2 units that are about twice the size of the servo amps.
    Alarm 59...
  17. Replies
    10
    Views
    10,771

    Re: 12 alarms on Fanuc 18i-TB

    The fan alarms are common on a machine that has sit for a period of time and the amps are dirty. If you hold your hand up over the top of the amplifiers you'll find that the fans are not running. You...
Results 1 to 17 of 17