Fanuc Ladder passwords

Sculptor,
this works great thank you for the help. Does not work for the Fanuc Robo Cut wire EDM 180 OiC control, any help there?
Ash.

Ash, please send me one locked, and one unlocked file, and i will try to find solution, when i find time.

ifihadarubbertree,
for SB4/SB6, offsets 0x31e and 0x340 are used, as you said. ASCII character values are encoded by using XOR encoding ( http://en.wikipedia.org/wiki/Simple_XOR_cipher ) and key 0x8c, 0x82, 0x9c, 0xaa, 0x86, 0xa0, 0x9a, 0x86 (i-th password's character is encoded by using i-th key's value).

Sculptor,

Thanks, I am going to use this as an idea for my first .net app. I haven't programmed in over 6 years and need to get back into it. Thanks for posting your source and your comments, they really help. This should be a good challenge and learning experience for me :).

Thanks again,

-Tree

Try my program in VB.... It's easy, fast and free!

RapidShare: Easy Filehosting

NOTE: This program NOT view you the password but find and remove the file download from cnc.
I remember: is possible you install .NET framework!

Send backup flie to me , i will sent you back with cracked password

best regards

my email is // tanatats(at)gmail.com //

[filichev]

It's easy way to learn objective-c and cocoa )))

Porting this software for Mac with GUI (Compiled for intel 64bit. If some people needs 32bit or ppc - ask me here)

depositfiles.com/files/uou5lo0f7
rapidshare.com/files/389586920/FanucGetPass.zip.html

[bdrk]

Dear OTC
I have try download your link but unfortunately deleted....could you send to me yor program
Best Regards
BdRk

[quique195]

hello check please secuense the password is tide to read Ladder it is control fanuc 18t or 18i

[namnp2007]

Originally Posted by Sculptor

It is easy. Since GetPass is a command line app, you need to use it in command line.
Suppose you have a memory card format file, say PMC.200 in folder C:\backup\emag\vl5\100459\ and that the GetPass utility is in folder C:\utils\ .
First you need to open a command line prompt: Start -> Run: cmd
A command line window will pop out.
Then you browse to the getpass utility by typing: CD c:\utils
If you want to examine folder content, use command: DIR.
Then you start getpass and pass path to memory card format file: GETPASS c:\backup\emag\vl5\100459\pmc.200
Program will output results and quit.
You can close command line window by typing: EXIT

Please send me memory card format files that cannot be unlocked by current version of GetPass.

@ sculptor
pls. sent me your e-mail address( namnp2007(at)gmail.com) if you can remove the passworld from Oi memory card formate files. I"ll sent you the files.

[Buzz]

Any word on a new link to the ladder pw exe as they have been deleted?
Any email for sculptor email or program use?
Thank, Buzz

[namnp2007]

Originally Posted by Buzz

Any word on a new link to the ladder pw exe as they have been deleted?
Any email for sculptor email or program use?
Thank, Buzz

Dear Buzz
sculptor not sent me his e-mail yet, and any link for software was died.
But I can remove the pw from memcard files any way. If you need, pls. sent me the files, i'll sent you those files witch pw removed,
Nam.

[Buzz]

Thanks for the quick reply. I did find the sw & so far have tested on pmc ladder types; RA, RB, SB, & NB.
Buzz

[arumugamsfl]

i have tried to crack the password i am not able to get can any body help me to get password.

[namnp2007]

Dear arumugamsfl
Please PM me : namnp2007(at) gmail.com
Hope to help.